Hampton Bay UC7080T Remote

What Is the UC7080T, Anyway?

The UC7080T is a handheld remote control designed to operate ceiling fans and integrated light kits. It usually comes paired with a UC7067FMRX receiver (don’t worry, you don’t have to memorize that). It features buttons for:

• Fan speed – High, Medium, Low
• Fan off
• Light on/off
• Dimming (for compatible dimmable bulbs)

In theory, it should just work. In reality, it sometimes needs a little encouragement.

How to Program or Pair the UC7080T Remote

This remote doesn’t require pairing in the modern Bluetooth/Wi-Fi sense. It communicates with the receiver via radio frequency (RF), and the two devices must be set to the same frequency using DIP switches.

Step-by-Step Pairing Instructions

1. Kill the power. Turn off power at the wall switch or breaker. Trust me, no one wants a surprise shock.
2. Open the remote battery cover. Inside, you’ll find a row of 4 tiny sliding DIP switches. Take note of the pattern.
3. Access the receiver inside the fan canopy. This is the fun part. You’ll need a ladder and probably a screwdriver. Once you lower the canopy, you’ll see a small black box—the receiver. It also has 4 DIP switches.
4. Match the DIP switch pattern. Set the switches on the remote and receiver to be identical. They must match exactly for the remote to talk to the fan.
5. Reassemble and restore power. Close everything back up, restore power, and test the remote. You should now be able to control the fan and light.

If you have multiple fans in the house using UC7080T remotes, give each remote/receiver pair a different DIP switch code to avoid unwanted cross-talk. (Unless you like turning on your bedroom fan every time someone in the kitchen hits a button.)

Troubleshooting the UC7080T – When It Stops Cooperating

Here’s a breakdown of what to do when your trusty UC7080T acts like it’s on strike.

Problem: Nothing Works – Fan or Light

• Check the batteries. Always start here. Even if they’re “new,” swap them out with confirmed fresh ones.
• Ensure the wall switch is on. The remote only works if the fan has power.
• Double-check the DIP switch settings. One tiny toggle out of place will break the connection.
• Try a full reset: kill power for 60 seconds, turn it back on, and then press the light button or speed buttons repeatedly.

Problem: Fan Works but Light Doesn’t (or Vice Versa)

• Verify bulb type. If you’re using smart bulbs or non-dimmable LEDs, the dimmer feature may cause issues.
• Try holding the light button down to trigger the dimmer mode. Some light kits won’t respond unless held.
• If the light flickers or doesn’t turn on, the problem could be a failed light kit or bad wiring—not the remote.

Problem: Intermittent Signal

• Move other wireless devices away from the fan—microwaves, routers, even baby monitors can interfere.
• Make sure the antenna wire on the receiver (yes, there’s a little wire) is hanging freely inside the canopy and not squished in a metal bracket.
• Replace the receiver if all else fails. They’re affordable and easy to swap out if you’re comfortable with wiring.

Can You Replace the UC7080T Remote?

Yes! If your remote has officially ghosted you, there are plenty of compatible replacements available online. Search specifically for “UC7080T” or get a universal Hampton Bay remote kit. These usually come with both a new remote and a matching receiver, so you don’t have to worry about compatibility or trying to find that one DIP switch combination that works.

The UC7080T may not have touchscreens, voice control, or wireless charging—but it’s a solid little device that’s kept countless fans running over the years. If yours is being temperamental, 90% of the time it’s an easy fix: batteries, DIP switches, or just a bit of TLC. And if it finally gives up the ghost? Swapping it out for a new one is cheaper than replacing the entire fan.

Now climb down off the ladder, put the screwdriver away, and enjoy the quiet breeze of success. You’ve earned it.